Signature Tower Jakarta

Jakarta

Note: As this project is proposed, the data is based on the most reliable information currently available. This data is thus subject to change until the building has completed and all information can be confirmed and ratified by the CTBUH.

Height
1
To Tip:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest point of the building, irrespective of material or function of the highest element (i.e., including antennae, flagpoles, signage and other functional-technical equipment).
638 m / 2,093 ft
2
Architectural:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the architectural top of the building, including spires, but not including antennae, signage, flag poles or other functional-technical equipment. This measurement is the most widely utilized and is employed to define the Council on Tall Buildings and Urban Habitat (CTBUH) rankings of the "World's Tallest Buildings."
638 m / 2,093 ft
3
Occupied:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest occupied floor within the building.
515.8 m / 1,692 ft
1 2 3 Signature Tower Jakarta
  Floors
Above Ground
The number of floors above ground should include the ground floor level and be the number of main floors above ground, including any significant mezzanine floors and major mechanical plant floors. Mechanical mezzanines should not be included if they have a significantly smaller floor area than the major floors below. Similarly, mechanical penthouses or plant rooms protruding above the general roof area should not be counted. Note: CTBUH floor counts may differ from published accounts, as it is common in some regions of the world for certain floor levels not to be included (e.g., the level 4, 14, 24, etc. in Hong Kong).
113
Below Ground
The number of floors below ground should include all major floors located below the ground floor level.
6
Height 638 m / 2,093 ft
Floors 113
Official Name
The current legal building name.

Signature Tower Jakarta

Other Names
Other names the building has commonly been known as, including former names, common informal names, local names, etc.

The Signature Tower

Type
CTBUH collects data on two major types of tall structures: 'Buildings' and 'Telecommunications / Observation Towers.' A 'Building' is a structure where at least 50% of the height is occupied by usable floor area. A 'Telecommunications / Observation Tower' is a structure where less than 50% of the structure's height is occupied by usable floor area. Only 'Buildings' are eligible for the CTBUH 'Tallest Buildings' lists.

Building

Status
Completed
Architecturally Topped Out
Structurally Topped Out
Under Construction
Proposed
On Hold
Never Completed
Vision
Competition Entry
Canceled
Proposed Renovation
Under Renovation
Renovated
Under Demolition
Demolished

Proposed

Country
The CTBUH follows the United Nations's definition of Country, and thus uses the lists and codes established by that organization.

Indonesia

City
The CTBUH follows the United Nations's definition of City, and thus uses the lists and codes established by that organization.

Jakarta

Address

Sudirman Central Business District

Function
A single-function tall building is defined as one where 85% or more of its usable floor area is dedicated to a single usage. Thus a building with 90% office floor area would be said to be an "office" building, irrespective of other minor functions it may also contain.

A mixed-use tall building contains two or more functions (or uses), where each of the functions occupy a significant proportion of the tower's total space. Support areas such as car parks and mechanical plant space do not constitute mixed-use functions. Functions are denoted on CTBUH "Tallest Building" lists in descending order, e.g., "hotel/office" indicates hotel function above office function.

Hotel / Office

Structural Material
All-Steel
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from steel. Note that a building of steel construction with a floor system of concrete planks or concrete slab on top of steel beams is still considered an “all-steel” structure as the concrete elements are not acting as the primary structure.

All-Concrete
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from concrete which has been cast in place and utilizes steel reinforcement bars and/or steel reinforced concrete which has been precast as individual components and assembled together on-site.

All-Timber
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from timber. An all-timber structure may include the use of localized non-timber connections between timber elements. Note that a building of timber construction with a floor system of concrete planks or concrete slab on top of timber beams is still considered an “all-timber” structure as the concrete elements are not acting as the primary structure.

Mixed-Structure
Utilizes distinct systems (e.g. all-steel, all-concrete, all-timber), one on top of the other. For example, a Steel Over Concrete indicates an all-steel structural system located on top of an all-concrete structural system, with the opposite true of Concrete Over Steel.

Composite
A combination of materials (e.g. steel, concrete, timber) are used together in the main structural elements. Examples include buildings which utilize: steel columns with a floor system of reinforced concrete beams; a steel frame system with a concrete core; concrete-encased steel columns; concrete-filled steel tubes; etc. Where known, the CTBUH database breaks out the materials used within a composite building’s primary structural elements.

Composite

Official Website

Signature Tower Signature Tower

Height
Architectural
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the architectural top of the building, including spires, but not including antennae, signage, flag poles or other functional-technical equipment. This measurement is the most widely utilized and is employed to define the Council on Tall Buildings and Urban Habitat (CTBUH) rankings of the "World's Tallest Buildings."

638 m / 2,093 ft

To Tip
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest point of the building, irrespective of material or function of the highest element (i.e., including antennae, flagpoles, signage and other functional-technical equipment).
638 m / 2,093 ft
Occupied
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest occupied floor within the building.
515.8 m / 1,692 ft
Observatory
515.8 m / 1,692 ft
Floors Above Ground
The number of floors above ground should include the ground floor level and be the number of main floors above ground, including any significant mezzanine floors and major mechanical plant floors. Mechanical mezzanines should not be included if they have a significantly smaller floor area than the major floors below. Similarly, mechanical penthouses or plant rooms protruding above the general roof area should not be counted. Note: CTBUH floor counts may differ from published accounts, as it is common in some regions of the world for certain floor levels not to be included (e.g., the level 4, 14, 24, etc. in Hong Kong).

113

Floors Below Ground
The number of floors below ground should include all major floors located below the ground floor level.

6

# of Hotel Rooms
Number of Hotel Rooms refers to the total number of hotel rooms contained within a particular building.

300

# of Parking Spaces
Number of Parking Spaces refers to the total number of car parking spaces contained within a particular building.

3001

Architect
Architect of Record

Usually takes on the balance of the architectural effort not executed by the "Design Architect," typically responsible for the construction documents, conforming to local codes, etc. May often be referred to as "Executive," "Associate," or "Local" Architect, however, for consistency CTBUH uses the term "Architect of Record" exclusively.
PDW Architects
Structural Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.
PT Gistama Intisemesta; Thornton Tomasetti
MEP Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.
Beca Group
Other Consultant

Other Consultant refers to other organizations which provided significant consultation services for a building project (e.g. wind consultants, environmental consultants, fire and life safety consultants, etc).
Geotechnical
Langan Engineering
Material Supplier

Material Supplier refers to organizations which supplied significant systems/materials for a building project (e.g. elevator suppliers, facade suppliers, etc).
Formwork
Doka GmbH
Owner
PT Grahamas Adisentosa
Developer
Artha Graha Group; PT Grahamas Adisentosa
Architect
Design

Usually involved in the front end design, with a "typical" condition being that of a leadership role through either Schematic Design or Design Development, and then a monitoring role through the CD and CA phases.
Smallwood, Reynolds, Stewart, Stewart
Architect of Record

Usually takes on the balance of the architectural effort not executed by the "Design Architect," typically responsible for the construction documents, conforming to local codes, etc. May often be referred to as "Executive," "Associate," or "Local" Architect, however, for consistency CTBUH uses the term "Architect of Record" exclusively.
PDW Architects
Structural Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.
PT Gistama Intisemesta; Thornton Tomasetti
MEP Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.
Beca Group; PT Hantaran Prima Mandiri
Other Consultant

Other Consultant refers to other organizations which provided significant consultation services for a building project (e.g. wind consultants, environmental consultants, fire and life safety consultants, etc).
Geotechnical
Langan Engineering
Quantity Surveyor
Langdon & Seah
Material Supplier

Material Supplier refers to organizations which supplied significant systems/materials for a building project (e.g. elevator suppliers, facade suppliers, etc).
Formwork
Doka GmbH

CTBUH Initiatives

What Makes Tall, Tall

29 September 2015 - Event

CTBUH Launches Indonesia Chapter

5 July 2013 - Event

See more

Videos

17 October 2016 | Jakarta

Mega Size Mixed-Use Projects: Redefining Vertical Urbanism

Monday October 17, 2016. Shenzhen, China. Dennis Poon of Thornton Tomasetti, presents at the 2016 China Conference Session 4c: Structural & Geotechnic Engineering. As the...

See more

Research

20 March 2020

Interactive Study on The Tallest 20 in 2020: Then and Now

CTBUH Research

This research paper undertakes a review of the 2012 report by the Council on Tall Buildings and Urban Habitat, “Tallest 20 in 2020: Entering the...

See more

Videos

Filter by

17 October 2016 | Jakarta

Mega Size Mixed-Use Projects: Redefining Vertical Urbanism

Monday October 17, 2016. Shenzhen, China. Dennis Poon of Thornton Tomasetti, presents at the 2016 China Conference Session 4c: Structural & Geotechnic Engineering. As the...

21 September 2012 | Jakarta

Interview: Signature Tower Jakarta

Sugeng Wijanto of PT Gistama Intisemesta and Tiyok Prasetyoadi of PDW Architects are interviewed by Jeff Herzer during the 2012 CTBUH Shanghai Congress at the...

21 September 2012 | Jakarta

The Signature Tower: Reaching High in the Sky of Indonesia

This presentation discusses the reasons behind the selection of the structural systems, as well as the use of advanced structural analyses and design methods, including...

Research

20 March 2020

Interactive Study on The Tallest 20 in 2020: Then and Now

CTBUH Research

This research paper undertakes a review of the 2012 report by the Council on Tall Buildings and Urban Habitat, “Tallest 20 in 2020: Entering the...

19 September 2012

The Signature Tower: Reaching High in the Sky of Indonesia

Sugeng Wijanto, Gistama Intisemesta; Tiyok Prasetyoadi, PDW Architects; Dennis Poon, Thornton Tomasetti; Wayan Sengara, Institut Teknologi Bandung-Indonesia

This presentation discusses the reasons behind the selection of the structural systems, as well as the use of advanced structural analyses and design methods, including...

18 January 2012

The Tallest 20 in 2020: Entering the Era of the Megatall

Nathaniel Hollister & Antony Wood, CTBUH

Within this decade we will likely witness not only the world’s first kilometer-tall building, but also the completion of a significant number of buildings over...

CTBUH Initiatives

Filter by

29 September 2015

What Makes Tall, Tall

CTBUH Atlanta recently hosted an event focusing on the design and construction criteria unique to tall buildings, asking what makes tall, tall?

5 July 2013

CTBUH Launches Indonesia Chapter

At the site of the future Signature Tower a discussion was held on the rapid growth experienced by Indonesia drawing more than 100 participants.

8 December 2011

The Tallest 20 in 2020: Entering the Era of the Megatall

Within this decade we will likely witness not only the world’s first kilometer-tall building, but also the completion of a significant number of buildings over 600 meters.