8 Chifley

Sydney
Height
1
To Tip:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest point of the building, irrespective of material or function of the highest element (i.e., including antennae, flagpoles, signage and other functional-technical equipment).
140.5 m / 461 ft
2
Architectural:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the architectural top of the building, including spires, but not including antennae, signage, flag poles or other functional-technical equipment. This measurement is the most widely utilized and is employed to define the Council on Tall Buildings and Urban Habitat (CTBUH) rankings of the "World's Tallest Buildings."
140.5 m / 461 ft
3
Occupied:
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest occupied floor within the building.
111.7 m / 366 ft
1 2 3 8 Chifley
  Floors
Above Ground
The number of floors above ground should include the ground floor level and be the number of main floors above ground, including any significant mezzanine floors and major mechanical plant floors. Mechanical mezzanines should not be included if they have a significantly smaller floor area than the major floors below. Similarly, mechanical penthouses or plant rooms protruding above the general roof area should not be counted. Note: CTBUH floor counts may differ from published accounts, as it is common in some regions of the world for certain floor levels not to be included (e.g., the level 4, 14, 24, etc. in Hong Kong).
24
Below Ground
The number of floors below ground should include all major floors located below the ground floor level.
2
Height 140.5 m / 461 ft
Floors 24
Official Name
The current legal building name.

8 Chifley

Other Names
Other names the building has commonly been known as, including former names, common informal names, local names, etc.

8 Chifley Square

Type
CTBUH collects data on two major types of tall structures: 'Buildings' and 'Telecommunications / Observation Towers.' A 'Building' is a structure where at least 50% of the height is occupied by usable floor area. A 'Telecommunications / Observation Tower' is a structure where less than 50% of the structure's height is occupied by usable floor area. Only 'Buildings' are eligible for the CTBUH 'Tallest Buildings' lists.

Building

Status
Completed
Architecturally Topped Out
Structurally Topped Out
Under Construction
Proposed
On Hold
Never Completed
Vision
Competition Entry
Canceled
Proposed Renovation
Under Renovation
Renovated
Under Demolition
Demolished

Completed

Completion

2013

Country
The CTBUH follows the United Nations's definition of Country, and thus uses the lists and codes established by that organization.

Australia

City
The CTBUH follows the United Nations's definition of City, and thus uses the lists and codes established by that organization.

Sydney

Function
A single-function tall building is defined as one where 85% or more of its usable floor area is dedicated to a single usage. Thus a building with 90% office floor area would be said to be an "office" building, irrespective of other minor functions it may also contain.

A mixed-use tall building contains two or more functions (or uses), where each of the functions occupy a significant proportion of the tower's total space. Support areas such as car parks and mechanical plant space do not constitute mixed-use functions. Functions are denoted on CTBUH "Tallest Building" lists in descending order, e.g., "hotel/office" indicates hotel function above office function.

Office

Structural Material
All-Steel
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from steel. Note that a building of steel construction with a floor system of concrete planks or concrete slab on top of steel beams is still considered an “all-steel” structure as the concrete elements are not acting as the primary structure.

All-Concrete
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from concrete which has been cast in place and utilizes steel reinforcement bars and/or steel reinforced concrete which has been precast as individual components and assembled together on-site.

All-Timber
Both the main vertical/lateral structural elements and the floor spanning systems are constructed from timber. An all-timber structure may include the use of localized non-timber connections between timber elements. Note that a building of timber construction with a floor system of concrete planks or concrete slab on top of timber beams is still considered an “all-timber” structure as the concrete elements are not acting as the primary structure.

Mixed-Structure
Utilizes distinct systems (e.g. all-steel, all-concrete, all-timber), one on top of the other. For example, a Steel Over Concrete indicates an all-steel structural system located on top of an all-concrete structural system, with the opposite true of Concrete Over Steel.

Composite
A combination of materials (e.g. steel, concrete, timber) are used together in the main structural elements. Examples include buildings which utilize: steel columns with a floor system of reinforced concrete beams; a steel frame system with a concrete core; concrete-encased steel columns; concrete-filled steel tubes; etc. Where known, the CTBUH database breaks out the materials used within a composite building’s primary structural elements.

Concrete-Steel Composite

Energy Label

5.0 Star NABERS Energy Rating; 6 Star Green Star

Official Website

8 Chifley

Height
Architectural
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the architectural top of the building, including spires, but not including antennae, signage, flag poles or other functional-technical equipment. This measurement is the most widely utilized and is employed to define the Council on Tall Buildings and Urban Habitat (CTBUH) rankings of the "World's Tallest Buildings."

140.5 m / 461 ft

To Tip
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest point of the building, irrespective of material or function of the highest element (i.e., including antennae, flagpoles, signage and other functional-technical equipment).
140.5 m / 461 ft
Occupied
Height is measured from the level of the lowest, significant, open-air, pedestrian entrance to the highest occupied floor within the building.
111.7 m / 366 ft
Observatory
111.7 m / 366 ft
Floors Above Ground
The number of floors above ground should include the ground floor level and be the number of main floors above ground, including any significant mezzanine floors and major mechanical plant floors. Mechanical mezzanines should not be included if they have a significantly smaller floor area than the major floors below. Similarly, mechanical penthouses or plant rooms protruding above the general roof area should not be counted. Note: CTBUH floor counts may differ from published accounts, as it is common in some regions of the world for certain floor levels not to be included (e.g., the level 4, 14, 24, etc. in Hong Kong).

24

Floors Below Ground
The number of floors below ground should include all major floors located below the ground floor level.

2

# of Parking Spaces
Number of Parking Spaces refers to the total number of car parking spaces contained within a particular building.

32

# of Elevators
Number of Elevators refers to the total number of elevator cars (not shafts) contained within a particular building (including public, private and freight elevators).

10

Tower GFA
Tower GFA refers to the total gross floor area within the tower footprint, not including adjoining podiums, connected buildings or other towers within the development.

21,700 m² / 233,577 ft²

Rankings

#
8159
Tallest in the World
#
199
Tallest in Oceania
#
194
Tallest in Australia
#
53
Tallest in Sydney

Construction Schedule

2010

Construction Start

2013

Completed

Owner/Developer
Architect
Design

Usually involved in the front end design, with a "typical" condition being that of a leadership role through either Schematic Design or Design Development, and then a monitoring role through the CD and CA phases.

Structural Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.

MEP Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.

Contractor
Main Contractor

The main contractor is the supervisory contractor of all construction work on a project, management of sub-contractors and vendors, etc. May be referred to as "Construction Manager," however, for consistency CTBUH uses the term "Main Contractor" exclusively.

Other Consultant

Other Consultant refers to other organizations which provided significant consultation services for a building project (e.g. wind consultants, environmental consultants, fire and life safety consultants, etc).

Façade

These are firms that consult on the design of a building's façade. May often be referred to as "Cladding," "Envelope," "Exterior Wall," or "Curtain Wall" Consultant, however, for consistency CTBUH uses the term "Façade Consultant" exclusively.

Landscape
Owner/Developer
Architect
Design

Usually involved in the front end design, with a "typical" condition being that of a leadership role through either Schematic Design or Design Development, and then a monitoring role through the CD and CA phases.

Architect of Record

Usually takes on the balance of the architectural effort not executed by the "Design Architect," typically responsible for the construction documents, conforming to local codes, etc. May often be referred to as "Executive," "Associate," or "Local" Architect, however, for consistency CTBUH uses the term "Architect of Record" exclusively.

Lippmann Partnership
Structural Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.

MEP Engineer
Design

The Design Engineer is usually involved in the front end design, typically taking the leadership role in the Schematic Design and Design Development, and then a monitoring role through the CD and CA phases.

Project Manager

The CTBUH lists a project manager when a specific firm has been commissioned to oversee this aspect of a tall building’s design/construction. When the project management efforts are handled by the developer, main contract, or architect, this field will be omitted.

Simon Healy
Contractor
Main Contractor

The main contractor is the supervisory contractor of all construction work on a project, management of sub-contractors and vendors, etc. May be referred to as "Construction Manager," however, for consistency CTBUH uses the term "Main Contractor" exclusively.

Other Consultant

Other Consultant refers to other organizations which provided significant consultation services for a building project (e.g. wind consultants, environmental consultants, fire and life safety consultants, etc).

Access
Morris Goding Accessibility Consulting
Acoustics
Renzo Tonin & Associates
Artist
Jenny Holzer; Barbara Flynn
Code
Philip Chun Group
Façade

These are firms that consult on the design of a building's façade. May often be referred to as "Cladding," "Envelope," "Exterior Wall," or "Curtain Wall" Consultant, however, for consistency CTBUH uses the term "Façade Consultant" exclusively.

Geotechnical
Douglas Partners
Landscape
Material Supplier

Material Supplier refers to organizations which supplied significant systems/materials for a building project (e.g. elevator suppliers, facade suppliers, etc).

Paint/Coating
AkzoNobel

CTBUH Awards & Distinctions

Best Tall Building, by Region, Asia & Australasia 2014 Award of Excellence

2014 CTBUH Awards

 

CTBUH Initiatives

CTBUH Executive Director Presents at Chapter Events in Australia

7 March 2017 - Event

Executive Director Visits Sydney and Melbourne

6 March 2017 - Event

Research

01 July 2018

A Human-Scaled Future for Dense Development

Ivan Harbour, Rogers Stirk Harbour + Partners

Critics of height argue that it de-humanizes our cities. Yet a critical mass is a necessity for vibrant city life, and height is a key...

About 8 Chifley

The tower at 8 Chifley provides functional quality offices while creating opportunities for connectivity between occupiers from different parts of the building. The office spaces across 21 levels are connected by a series of adaptable two- and three-story interlinked vertical “villages.” These villages, ranging in size from 1,800 to 2,600 square meters, provide the building with a high degree of flexibility, while creating a variety of individual workspace environments that allow privacy and interaction between individuals. This floor space, within a void, and yet within the tower, allows the redistribution of space higher up the building where better views can be enjoyed. The villages are interspersed with full-floor office levels, which allow for multiple villages to be connected. These dramatic vertical business units, each of up to four floors, frame the magnificent views over the cityscape. The larger “villages” create 45 percent more perimeter space with enhanced natural light, compared to traditional floorplates, providing flexibility for either open-plan or cellular-office layouts.

Central to the building’s sense of connectivity and community is the building’s social heart: its elevated “village square,” on the 18th floor, set within a three-story void. This landscaped space contains a glass pavilion for all-weather use. The profiled roof allows level 30 to take on similar qualities to the loggia spaces at ground level and at level 18. Framed by a wind-permeable structure that neutralizes the wind load, the light structure provides shading to the terrace, while allowing an open character.

On a prominent, north-facing site, 8 Chifley makes the most of its small site, which, unusually, is open on three sides, the new building reaches to the edges of its site, opens up at the lower six floors, forming a large public space that addresses one of Sydney’s few existing city squares. This tight site presents a number of logistical construction challenges, which led to extensive use of offsite manufacture and well-timed deliveries to keep to a tight program. Construction started following the demolition of the existing Goodsell building.

The design aims to create a building whose carbon emissions are at least 50 per cent less than those of a “typical” Sydney CBD office, through a wide-ranging environmental design strategy. The blackwater recycling plant for the treatment and reuse of building and main water reduces the building’s demand on potable water supply and discharges. A tri-generation system provides onsite base building power, heating and cooling and peak load reduction from the existing electricity grid. The tri-generation system is also capable of exporting power to other buildings at certain times of the year. A chilled-beam mechanical system reduces energy use and requires a high volume of fresh-air intake. The high-efficiency façade, including external shading and performance glazing reducing heat load, directs sunlight and daylight glare. A naturally ventilated ground floor glass lobby enclosure allows cooling without extensive energy expenditure. The interiors use low volatile organic compound (VOC) materials and minimize the use of polyvinyl chloride (PVC). Basement facilities accommodate cyclists through bike racks, change rooms and lockers, and the roof is designed to accommodate photovoltaic cells at a future date, while a shower and accessible bathroom are provided on each level. In all, these strategies contribute to the building’s 6-Star Green Star rating, the highest achievable in Australia.

CTBUH Awards & Distinctions

Best Tall Building, by Region, Asia & Australasia 2014 Award of Excellence

2014 CTBUH Awards

01 July 2018

A Human-Scaled Future for Dense Development

Ivan Harbour, Rogers Stirk Harbour + Partners

Critics of height argue that it de-humanizes our cities. Yet a critical mass is a necessity for vibrant city life, and height is a key...

26 October 2015

8 Chifley – Sustainable Structural and Fire Engineering

Andrew Johnson, Arup

8 Chifley’s unique aesthetic has attracted much of the attention, however the 34 storey 150m tall building’s overall quality, sustainable performance, and structural efficiency, both...

9 March 2017

CTBUH Executive Director Presents at Chapter Events in Australia

Executive Director Antony Wood delivered two well attended lectures in Sydney and Melbourne, organized by the respective local CTBUH committees.

10 March 2017

Executive Director Visits Sydney and Melbourne

CTBUH Executive Director Antony Wood traveled to Sydney and Melbourne to build support for the 2017 conference through meetings and lectures.

17 September 2015

Warm Weather Spaces Walking Tours 2015

The CTBUH Urban Habitat / Urban Design Committee organized guided walking tours of 16 cities around the globe, focusing on urban habitats around tall buildings.

29 July 2015

Ivan Harbour on Design Excellence

CTBUH Sydney welcomed Ivan Harbour, of Roger Stirk Harbour + Partners, to share his thoughts and experiences with international design excellence competitions.

30 April 2014

CTBUH in NSW Holds Launch Event

The CTBUH in New South Wales, Australia, launched with an evening event at 8 Chifley Square - one of Sydney's newest iconic tall buildings.